Steelcraft-automotive 211500 3 ROUND SIDE BAR Manuel d'utilisateur télécharger pdf

SIDEBAR

99-11 FORD RANGER REG CAB & SUPER CAB 2 DR

Page 1 of 3 6/2/11 Rev1(DP)

PARTS LIST:

Driver/Left Sidebar

Driver/Left Side 10-1.50mm Double Nut Plate

Passenger/Right Sidebar

Passenger/Right Side 10-1.50mm Double Nut Plate

Driver/Left Side Front Mounting Bracket

10-1.50mm x 30mm Hex Bolts

Passenger/Right Side Front Mounting Bracket

10mm Lock Washers

Driver/Left Side Front Support Bracket

10mm x 20mm OD x 2mm Flat Washers

Passenger/Right Side Front Support Bracket

10mm Hex Nuts

Driver/Left Side Rear Mounting Bracket

1/2” x 2” Hex Bolts

Passenger/Right Side Rear Mounting Bracket

1/2” Lock Washers

1/2” x 1-1/2” OD x 1/8” Flat Washers

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY BEFORE STARTING INSTALLATION.

2. From under the passenger side of the vehicle, locate the three factory holes (one large, two small) in

the frame channel next to the front body mount. Insert the smaller end of the passenger side Double

Nut Plate through the large hole in the frame and line it up with the smaller hole toward the front,

(Figure 1).

3. Hang the passenger side front Bracket from the Double Nut Plate with the included (2) 10mm x 30mm

Hex Bolts, (2) 10mm Lock Washers and (2) 10mm Flat Washers, (Figure 2).

4. Locate the factory hole on the edge of the floor panel behind the passenger front body mount. Select

the passenger side Front Support Bracket. Bolt the flat end of the Support Bracket to the factory hole

using the included (1) 10mm x 30mm Hex Bolt, (1) 10mm Lock Washer, (2) 10mm Flat Washers and

(1) 10mm Hex Nut, (Figure 3). Line up the bent end of the Support Bracket with the back of the front

Bracket. Leave Support Bracket hardware loose at this time.

5. Next, move towards the rear of the vehicle. Insert the passenger side rear Bracket up and between the

inner side panel and the outer body of the vehicle, (Figure 4 & 5). Line up the hole in the 90˚ bend with

the factory hole in the cab toward the bed and secure it using the included (1) 10mm x 30mm Hex Bolt,

(1) 10mm Lock Washer, (2) 10mm Flat Washers and (1) 10mm Hex Nut. Attach the upper mounting

location in the Rear Bracket to factory hole in the inner side panel using the included (1) 10mm x 30mm

Hex Bolt, (1) 10mm Lock Washer, (2) 10mm Flat Washers and (1) 10mm Hex Nut, (Figure 4 & 5). Do

not tighten hardware at this time. NOTE: On some models, it may be necessary to drill a hole through

Driver/Left Side

Front Bracket

Passenger/Right

Side Front Bracket

Passenger/Right Side

Rear Bracket

Driver/Left Side

Rear Bracket

Driver/Left Side Front

Support Bracket

Passenger/Right Side

Front Support Bracket

Driver/Left Side

Double Nut Plate

Passenger/Right Side

Double Nut Plate

1 2 3

SIDEBAR 3

Résumé du contenu

Page 1

SIDEBAR 99-11 FORD RANGER REG CAB & SUPER CAB 2 DR Page 1 of 3 6/2/11 Rev1(DP) PARTS LIST:

Page 2

SIDEBAR 99-11 FORD RANGER REG CAB & SUPER CAB 2 DR Page 2 of 3 6/2/11 Rev1(DP) the side panel fo

Page 3 - SIDEBAR

SIDEBAR 99-11 FORD RANGER REG CAB & SUPER CAB 2 DR Page 3 of 3 6/2/11 Rev1(DP) Passenger Sidebar

Commentaires sur ces manuels

Pas de commentaire

Steelcraft-automotive 211500 3 ROUND SIDE BAR Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Steelcraft-automotive 211500 3 ROUND SIDE BAR. Steelcraft Automotive 211500 3 ROUND SIDE BAR User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Steelcraft-automotive 211500 3 ROUND SIDE BAR