Steelcraft-automotive 413709 5 OVAL SIDE BAR Manuel d'utilisateur télécharger pdf

5” STRAIGHT OVAL SIDEBAR

09-14 FORD F-150 SUPER CAB

Page 1 of 2 4/14/14Rev1(DP)

PARTS LIST:

Qty

Description

Qty

Description

Driver/Left Side Bar

8-1.25mm x 25mm Hex Bolts

Passenger/Right Side Bar

8mm x 28mm OD x 3mm Flat Washers

Driver/Left Front-Passenger/Right Rear

Mounting Brackets

8mm x 24mm OD x 2mm Flat Washers

Passenger/Right Front- Driver/Left Rear

Mounting Brackets

8mm Lock Washers

8mm Deep Clip Nuts

8mm Hex Nuts

8-1.25mm x 30mm Hex Bolts

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY BEFORE STARTING INSTALLATION.

2. Starting on the driver side of the vehicle, locate the (2) holes in the pinch weld to find the factory

mounting holes in the inner side panel, (Figure 1). NOTE: The inner holes may be covered with sealing

tape or insulation. Slide the 8mm Clip Nuts into the opening with the nut towards the inside. Line up the

threaded nut on the clip with the round holes, (Figure 1).

3. Partially attach the driver side Mounting Bracket to the Clip Nuts with the included (2) 8mm x 30mm

Hex Bolts, (2) 8mm Lock Washers and (2) 8mm x 28mm Large Flat Washers, (Figure 2). Depending

on model and year, the brake cable may be run on the inside or outside of the Bracket. Do not tighten

hardware at this time. NOTE: The Cradle on the Front Mounting Bracket should face to the rear of the

vehicle.

4. Align the bottom holes in the front Mounting Bracket with the (2) holes in the pinch weld. Bolt the

Bracket to the pinch weld using the included (2) 8mm x 25mm Hex Bolts, (2) 8mm Lock Washers, (4)

8mm STD Flat Washers and (2) 8mm Hex Nuts, (Figure 2). NOTE: Insert the bolts up from the bottom

of the pinch weld and through the Bracket.

5. Repeat Steps 2 – 4 for Rear Mounting Bracket installation. NOTE: The cradle on the Rear Mounting

Bracket should face the front of the vehicle, (Figures 3 & 4). The mounting holes will be the last set

towards the back of the cab.

6. Carefully position the Sidebar onto the Mounting Brackets and attach it using the included (4) 8mm x

25mm Hex Bolts, (4) 8mm Lock Washers and (4) 8mm STD Flat Washers, (Figure 4). Do not tighten

hardware at this time.

7. Level and adjust the Sidebar properly and tighten all hardware.

8. Repeat Steps 2 – 7 for passenger Sidebar installation.

9. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

Driver/Left Rear

Mounting Bracket

Driver/Left Front

Mounting Bracket

Passenger/Right Rear

Mounting Bracket

Passenger/Right Front

Mounting Bracket

Front

1 2

Résumé du contenu

Page 1

5” STRAIGHT OVAL SIDEBAR 09-14 FORD F-150 SUPER CAB Page 1 of 2 4/14/14Rev1(DP) PARTS LIST: Qt

Page 2 - 09-14 FORD F-150 SUPER CAB

5” STRAIGHT OVAL SIDEBAR 09-14 FORD F-150 SUPER CAB Page 2 of 2 4/14/14Rev1(DP) To protect your investm

Commentaires sur ces manuels

Pas de commentaire

Steelcraft-automotive 413709 5 OVAL SIDE BAR Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Steelcraft-automotive 413709 5 OVAL SIDE BAR. Steelcraft Automotive 413709 5 OVAL SIDE BAR User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Steelcraft-automotive 413709 5 OVAL SIDE BAR