Steelcraft-automotive 121120 RUNNING BOARD Manuel d'utilisateur télécharger pdf

VIEWPOINT ALUMINUM RUNNING BOARD

2011-13 DODGE DURANGO

Page 1 of 3 9/5/12 (DP)

Parts List:

Driver/ Left Running Board

6mm “T” Bolts

Passenger/Right Running Board

6-1.0mm x 25mm Hex Bolts

Mounting Brackets

6mm x 22mm OD x 2mm Large Flat Washers

12-1.75mm x 40mm Bolt Plates

6mm x 18mm OD x 1.6mm STD Flat Washers

12mm Serrated Flange Nuts

6mm Lock Washers

12mm x 24mm OD x 2.5mm Flat Washers

6mm Hex Nuts

12mm Plastic Retainers

6mm Nylon Lock Nuts

PROCEDURE:

REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY BEFORE STARTING INSTALLATION.

1. Starting at the driver side, locate the (3) pairs of factory holes in the pinch weld, (Figure 1 & 2). Move

toward the front pair. Remove the rubber plug filling the oval hole in the bottom of the rocker panel in

front of the two holes, (Figure 3). Select (1) 12mm Bolt Plate and (1) 12mm Plastic Retainer. Partially

thread the Retainer onto the Bolt Plate. Insert the Bolt Plate into the hole and rotate it 90-degrees to go

across the slot, (Figure 4). Thread the Retainer all the way down the Bolt Plate and tight against the

body panel, (Figure 5). NOTE: The Plastic Retainer is designed to prevent the Bolt Plate from falling

into the body cavity and to aid in installing the Bracket.

2. Select (1) Mounting Bracket and secure it to the Bolt Plate with (1) 12mm x 24mm Flat Washer and (1)

12mm Serrated Flange Nut, (Figure 6). Do not tighten hardware at this time.

3. Line up the (2) small slots in the Bracket with the (2) holes in the pinch weld. Bolt the Bracket to the

outside of the pinch weld with (2) 6mm x 25mm Hex Bolts, (2) 6mm x 22mm Large Flat Washers,

(outside against Bracket), (2) 6mm x 18mm STD Flat Washers, (inside against pinch weld), and (2)

6mm Nylon Lock Nuts, (Figures 6 & 7). Do not tighten hardware at this time.

4. Repeat Steps 1 – 3 to install the center and rear Brackets, (Figure 2).

5. Select the driver/left side Running Board. Locate the openings cut at the end of the slots on the bottom

of the Running Board, (Figure 8). Insert (3) 6mm T-Bolts into each channel through the openings. Slide

the T-Bolts into the approximate position in line with the (3) Brackets. Carefully place the Running

Board in position on top of the Brackets. Slide the T-Bolts forward or back until they line up and drop

into the slots on the Brackets. Secure the Running Board to the Brackets with (6) 6mm x 22mm Large

Passenger/Right

Running Board

Driver/Left Running Board

(6) Mounting

Brackets

(6) 12mm x 40mm

Bolt Plates

Front

1 2 3

2011-13 DODGE DURANGO 3

Résumé du contenu

Page 1

VIEWPOINT ALUMINUM RUNNING BOARD 2011-13 DODGE DURANGO Page 1 of 3

Page 2

VIEWPOINT ALUMINUM RUNNING BOARD 2011-13 DODGE DURANGO Page 2 of 3

Page 3 - 2011-13 DODGE DURANGO

VIEWPOINT ALUMINUM RUNNING BOARD 2011-13 DODGE DURANGO Page 3 of 3

Commentaires sur ces manuels

Pas de commentaire

Steelcraft-automotive 121120 RUNNING BOARD Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Steelcraft-automotive 121120 RUNNING BOARD. Steelcraft Automotive 121120 RUNNING BOARD User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Steelcraft-automotive 121120 RUNNING BOARD