Steelcraft-automotive 223200 3 ROUND SIDE BAR Manuel d'utilisateur télécharger pdf

3" SIDEBARS

2011-14 JEEP GRAND CHEROKEE

Page 1 of 3 10/1/12 (DP)

PARTS LIST:

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY BEFORE STARTING INSTALLATION.

2. Starting at the passenger side front, locate the 3 pairs of (2) small holes in the pinch weld, (Figures 1 &

2). Remove the rubber plug filling the oval hole in the bottom of the rocker panel directly in front of the

(2) holes, (Figure 3). Select (1) 12mm Bolt Plate and (1) 12mm Plastic Retainer, (Figure 4A). Thread

the Retainer part way onto the Bolt Plate. NOTE: The Retainer will help hold the Bolt Plate in position

during Bracket installation. Insert the Bolt Plate into the hole and rotate 90-degrees to the slot, (Figures

4B & 5). Thread the Retainer down until it is tight against the sheet metal.

3. Select (1) Mounting Bracket and hang it from the Bolt Plate with (1) 12mm Flat Washer and (1) 12mm

Flange Nut, (Figures 6 & 7). Next, bolt the mounting plate on the Bracket to the front of the pinch weld

with (2) 6mm x 25mm Hex Bolts, (4) 6mm Flat Washers and (2) 6mm Nylon Lock Nuts. Snug but do not

fully tighten hardware at this time.

4. Repeat Steps 2 – 3 for center and rear Mounting Bracket installation.

5. Select the passenger/right Sidebar and carefully place it in position on the (3) Mounting Brackets. Line

up the threaded holes in the Sidebar with the slots in the Brackets and bolt it in place with the included

(6) 8mm x 25mm Hex Bolts, (6) 8mm Lock Washers and (6) 8mm Flat Washers, (Figure 8). Snug all

hardware but do not tighten at this time.

6. Adjust and level the Sidebar and tighten all hardware.

7. Repeat Steps 2 – 6 for passenger/right Sidebar installation.

8. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer

over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish.

For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap may be

used also to clean the Sidebar.

For gloss black finishes: Mild soap may be used to clean Sidebar.

Driver/Left Sidebar

12mm Serrated Flange Nuts

Passenger/Right Sidebar

8-1.25mm x 25mm Hex Bolts

Driver/Left Mounting Brackets

8mm x 24mm x 2mm Flat Washers

Passenger/Right Mounting Brackets

8mm Lock Washers

12-1.75mm x 40mm Bolt Plates

6-1.0mm x 25mm Hex Bolts

12mm Plastic Retainers

6mm x 18mm OD x 1.6mm Flat Washers

12mm x 24mm OD x 2.5mm Flat Washer

6mm Nylon Lock Nuts

(3) Passenger/Right

Mounting Brackets

(3) Driver/Left

Mounting Brackets

Driver/Left Rear

Mounting Bracket

(6) 12mm x 40mm

Bolt Plates

Passenger/Right Sidebar

Driver/Left Sidebar

Front

(6) 12mm x 40mm

Bolt Plates

1 2 3

Résumé du contenu

Page 1 - Bolt Plates

3" SIDEBARS 2011-14 JEEP GRAND CHEROKEE Page 1 of 3

Page 2

3" SIDEBARS 2011-14 JEEP GRAND CHEROKEE Page 2 of 3

Page 3 - 2011-14 JEEP GRAND CHEROKEE

3" SIDEBARS 2011-14 JEEP GRAND CHEROKEE Page 3 of 3

Commentaires sur ces manuels

Pas de commentaire

Steelcraft-automotive 223200 3 ROUND SIDE BAR Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Steelcraft-automotive 223200 3 ROUND SIDE BAR. Steelcraft Automotive 223200 3 ROUND SIDE BAR User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Steelcraft-automotive 223200 3 ROUND SIDE BAR