Steelcraft-automotive 455060 4 OVAL SIDE BAR Manuel d'utilisateur télécharger pdf

4" OVAL SIDEBAR

2003-2011 HONDA ELEMENT (EXCLUDES SC MODEL)

Tony Page 1 of 3 2/22/2012 Rev1 (DP)

PARTS LIST:

Driver/Left Sidebar

10mm Lock Washers

Passenger/Right Sidebar

10mm Hex Nuts

Front Mounting Brackets

8-1.25mm x 30mm Hex Bolts

Front Support Brackets

8-1.25mm x 25mm Hex Bolts

Rear Mounting Brackets

8-1.25mm x 20mm Flange Hex Bolts

10-1.5mm x 35mm Bolt Plates

8mm x 24mm x 2mm Flat Washers

10mm Plastic Retainers

8mm Lock Washers

10mm x 24mm OD x 2.2mm Flat Washer

8mm Hex Locking Flange Nuts

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY BEFORE STARTING INSTALLATION.

2. Select (1) Front Mounting Bracket and (1) Front Support Bracket, (Figure 1). Line up the (4) main

mounting holes in both brackets and bolt the Support Bracket to the bottom of the Mounting Bracket

with the included (4) 8mm x 20mm Flange Hex Bolts and (4) 8mm Locking Flange Nuts, (Figure 2).

Do not tighten hardware at this time.

3. Starting on the driver side front of the vehicle, locate the (2) factory threaded holes in the bottom of

the outer frame channel and the single threaded hole in the bottom of the inner frame channel,

(Figure 3A & 3B). NOTE: The threaded holes may be filled with plastic plugs or covered in

insulation. Remove plugs or insulation before proceeding.

4. Position the Front Mounting Bracket and Support Bracket up to the vehicle. Hang the Bracket

assembly from the two threaded holes using the provided (2) 8mm x 30mm Hex Bolts, (2) 8mm Lock

Washers and (2) 8mm Flat Washers, (Figure 4). Line up the slot in the end of the Support Bracket

with the threaded hole in the inner frame channel. Bolt the Support Bracket to the frame channel

with an 8mm x 30mm Hex Bolt, 8mm Lock Washer and 8mm Flat Washer. Snug but do not tighten

hardware at this time.

5. Move toward the rear of the vehicle and locate the (2) factory oval holes in the side of the body

panel, (Figure 5A). Thread (1) Plastic Retainer part way onto (1) 10mm Bolt Plate, (Figure 5B).

Insert the Bolt Plate and Retainer into the oval hole and thread the Plastic Retainer down against the

body panel, (Figure 5A). Rotate the Bolt Plate 90-degrees so that it is supported across the slot in

the body panel. IMPORTANT: The Plastic Retainer is designed to prevent the Bolt Plate from falling

into the body cavity and to aid in Bracket installation. Repeat this Step to install the second Bolt

Plate in the remaining factory oval hole.

(2) Rear Mounting Brackets

(2)Front Support Brackets

(2) Front Mounting

Brackets

(4) 10mm x 35mm Bolt Plates (Pictured

with Plastic Retainer and Hardware)

Front

Rear

1 2 3

4" OVAL SIDEBAR 3

Résumé du contenu

Page 1

4" OVAL SIDEBAR 2003-2011 HONDA ELEMENT (EXCLUDES SC MODEL) Tony Page 1 of 3 2/22/2012 Rev1 (DP) PARTS LIST: 1 Driver/Left Sidebar 4 10

Page 2

4" OVAL SIDEBAR 2003-2011 HONDA ELEMENT (EXCLUDES SC MODEL) Tony Page 2 of 3 2/22/2012 Rev1 (DP) 6. Select (1) Rear Mounting Bracket. Hang the

Page 3 - 4" OVAL SIDEBAR

4" OVAL SIDEBAR 2003-2011 HONDA ELEMENT (EXCLUDES SC MODEL) Page 3 of 3 2/22/2012 Rev1 (DP) Driver Side Installation Pictured

Commentaires sur ces manuels

Pas de commentaire

Steelcraft-automotive 455060 4 OVAL SIDE BAR Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Steelcraft-automotive 455060 4 OVAL SIDE BAR. Steelcraft Automotive 455060 4 OVAL SIDE BAR User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Steelcraft-automotive 455060 4 OVAL SIDE BAR