Steelcraft-automotive 52250 GRILL GUARD Manuel d'utilisateur télécharger pdf

Page 1 of 5 12/30/08 Rev2(DP)

PARTS LIST:

Qty

Description

Qty

Description

Grille Guard

12-1.75mm x 35mm Hex Bolts

Upper Frame Mounting Brackets (for trucks without

tow hooks only)

12mm x 30.1mm OD x 3.1mm Flat Washers

Driver/Left Lower Frame Mounting Bracket

12mm Lock Washers

Passenger/Right Lower Frame Mounting Bracket

12-1.75mm Hex Nuts

Driver/Left Upper Support Bracket

8mm x 20mm Button Head Allen Bolts

Passenger/Right Upper Support Bracket

8mm x 22mm OD x 1.5mm Flat Washers

Driver/Left Lower Support Bracket

8mm Lock Washers

Passenger/Right Lower Support Bracket

8mm Hex Nuts

12-1.5mm x 30mm Fine Thread Hex Bolt (for trucks

without tow hooks only)

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ

INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. CUTTING IS REQUIRED.

ASSISTANCE IS RECOMMENDED.

2. Starting at the underside of the front bumper, carefully remove the plastic splash guard. NOTE:

Depending on the model of truck, the splash guard may be attached to the bottom of the truck with

hex bolts and several two-piece plastic push-in clips. NOTE: Pay close attention to the type and

location of all factory hardware for reinstallation. First, remove all hex bolts then locate the clips

behind the bumper cover, (Figure 1A). Pry up on the center pin of the clip with a small flat blade

screwdriver and remove the entire clip, (Figure 1B). The splash guard may also be attached to

the bumper cover with rivets or hex bolts at the corners. NOTE: If the splash guard is fastened

with rivets, first remove all of the other fasteners from the splash guard. Hold the bumper cover in

place and firmly pull the splash guard from each rivet. Remove the rivets from the bumper cover

and move the splash guard to a clean stable work area.

3. From underneath the front of the vehicle, determine if the truck is equipped with or without tow

hooks.

INSTALLATION INSTRUCTIONS

GRILLE GUARD

09-ON DODGE RAM

PART #

Passenger Side

Lower Frame

Mounting

Bracket

Driver Side Lower

Frame Mounting

Bracket

Passenger Side

Lower Support

Bracket (see note)

Upper Frame

Mounting

Bracket (use on

trucks without

tow hooks only)

Upper Frame

Mounting

Bracket (use on

trucks without

tow hooks only)

Driver Side Lower Support Bracket

(Support Brackets pictured in position

for installation on tow hook equipped

vehicles. Reverse direction for

vehicles without tow hooks)

Passenger side Upper

Support Bracket

Driver side Upper

Support Bracket

1 2 3 4 5

INSTALLATION INSTRUCTIONS 1

Résumé du contenu

Page 1 - INSTALLATION INSTRUCTIONS

Page 1 of 5 12/30/08 Rev2(DP) PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Upper Frame Mo

Page 2

Page 2 of 5 12/30/08 Rev2(DP) For models without tow hooks: A. Select one of the Upper Frame Brackets and the driver side Lower Frame Mou

Page 3

Page 3 of 5 12/30/08 Rev2(DP) Use the included (1) 12mm x 35mm Hex Bolt, (2) 12mm Flat Washers, (1) 12mm Lock Washer and (1) 12mm Hex Nut,

Page 4

Page 4 of 5 12/30/08 Rev2(DP) Driver Side Installation Pictured Fig 4 Installatio

Page 5

Page 5 of 5 12/30/08 Rev2(DP) Driver Side Installation Pictured Do not cut through the front or rear edge of the splash guard Fig 10 If

Commentaires sur ces manuels

Pas de commentaire

Steelcraft-automotive 52250 GRILL GUARD Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Steelcraft-automotive 52250 GRILL GUARD. Steelcraft Automotive 52250 GRILL GUARD User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Steelcraft-automotive 52250 GRILL GUARD