Steelcraft-automotive 280310 3 ROUND SIDE BAR Manuel d'utilisateur télécharger pdf

3" SIDEBAR

2014 SORENTO

Page 1 of 6 10/3/13 (DP)

PARTS LIST:

Driver/Left Sidebar

12mm Lock Washers

Passenger/Right Sidebar

12mm Hex Nuts

Front Mounting Brackets

8-1.25mm x 25mm Hex Bolts

Front Support Brackets

8mm x 24mm x 2mm Flat Washers

Driver/Left Rear Mounting Bracket

8mm Lock Washers

Passenger/Right Rear Mounting Bracket

8mm Hex Nuts

14mm x 50mm x 4mm Flat Washers

6mm x 25mm Hex Bolts

12mm x 35mm Long Front Bolt Plate

6mm x 20mm OD x 2mm Flat Washers

12mm x 40mm Short Low Profile Rear Bolt

Plate

6mm Lock Washers

12mm x 32mm x 3mm Flat Washers

6mm Hex Nuts

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY BEFORE STARTING INSTALLATION. CUTTING AND DRILLING IS REQUIRED.

2. Starting at the front, driver side of the vehicle, locate and remove the plastic cover attached to the

bottom of the floor panel, (Figure 1). Next, locate and remove the rubber plug in the bottom of the inner

frame channel, (Figure 2). Insert (1) 12mm x 35mm Long Bolt Plate into the hole, (Figures 3A & 3B).

3. Select (1) Front Bracket and (1) Front Support Bracket, (Figure 4). Bolt the Support Bracket to the top

of the front Bracket with (2) 8mm x 25mm Hex Bolts, (4) 8mm Flat Washers, (2) 8mm Lock Washers

and (2) 8mm Hex Nuts. Snug but do not fully tighten hardware at this time.

4. Next, attach the front Bracket assembly to the Bolt Plate with (1) 12mm Flat Washer (1) 12mm Lock

Washer and (1) 12mm Hex Nut, (Figure 5). Leave hardware loose at this time.

5. Line up the mounting tab on the front Support Bracket with the back of the pinch weld. Use a clamp to

temporarily attach the Support Bracket to the pinch weld, (Figure 6).

6. Move toward the rear of the vehicle. Locate the rubber plug in the bottom of the floor panel directly in

front of the rear suspension mount, (Figure 7). Insert (1) 12mm x 40mm Short Low Profile Bolt Plate

into the hole, (Figures 8A & 8B). Slide (1) Large Spacer Washer over the Bolt Plate, (Figure 9A & 9B).

Attach the driver side Rear Bracket to the Spacer and Bolt Plate with (1) 12mm Flat Washer, (1) 12mm

Lock Washer and (1) 12mm Hex Nut, (Figure 9C).

7. Push the mounting tab on the Bracket up against the back of the pinch weld. Use a clamp to help hold

the Bracket in place if necessary. Tighten the 12mm Hex Nut only at this time. Mark the locations of the

slots on the mounting tab onto the back of the pinch weld, (Figure 12).

(2) Front Mounting Brackets

Passenger/

Right Rear

Mounting

Bracket

Driver/Left

Rear

Mounting

Bracket

(2) 12mm x 40mm Short

Low Profile Bolt Plates

(2) 12mm x 35mm Long

Bolt Plates

Front Support

Bracket

Front Support

Bracket

Driver Sidebar

Passenger Sidebar

Front

(4) Spacer Washers

1 2 3 4 5 6

3" SIDEBAR 3
2014 SORENTO 3

Résumé du contenu

Page 1

3" SIDEBAR 2014 SORENTO Page 1 of 6 10/3/13 (DP) PARTS LIST: 1 Driver/Left Sidebar

Page 2

3" SIDEBAR 2014 SORENTO Page 2 of 6 10/3/13 (DP) 8. Remove the plastic deflector in front

Page 3 - 2014 SORENTO

3" SIDEBAR 2014 SORENTO Page 3 of 6 10/3/13 (DP) Driver Side Installation Pictured

Page 4

3" SIDEBAR 2014 SORENTO Page 4 of 6 10/3/13 (DP) Driver Side Installation Pictured

Page 5

3" SIDEBAR 2014 SORENTO Page 5 of 6 10/3/13 (DP) Driver Side Installation Pictured

Page 6

3" SIDEBAR 2014 SORENTO Page 6 of 6 10/3/13 (DP) Driver Side Installation Pictured

Commentaires sur ces manuels

Pas de commentaire

Steelcraft-automotive 280310 3 ROUND SIDE BAR Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Steelcraft-automotive 280310 3 ROUND SIDE BAR. Steelcraft Automotive 280310 3 ROUND SIDE BAR User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Steelcraft-automotive 280310 3 ROUND SIDE BAR