Steelcraft-automotive 230900 3 ROUND SIDE BAR Manuel d'utilisateur télécharger pdf

3" SIDE BARS

05-12 TACOMA DOUBLE CAB

Page 1 of 2 11/23/11 RevC(DP)

Driver/Left Side Front

Mounting Bracket

Driver/Left Side Rear

Mounting Bracket

Driver/Left Side Center

Mounting Bracket

PARTS LIST:

Driver Sidebar

Driver/Left Rear Mounting Bracket

Passenger Sidebar

Passenger/Right Rear Mounting Bracket

Driver/Left Front Mounting Bracket

8-1.25mm x 30mm Hex Bolts

Passenger/Right Front Mounting Bracket

8mm Lock Washers

Driver/Left Middle Mounting Bracket

8mm ID x 24mm OD x 2mm Flat Washers

Passenger/Right Middle Mounting Bracket

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY. USE ILLUSTRATION TO PROPERLY IDENTIFY BRACKETS AND SIDEBARS.

2. Starting on the driver side front of the vehicle, use a flat screw driver to remove the plastic plugs

covering the threaded holes in the body panel, (Figure 1). Select the driver side front Mounting Bracket

and bolt it to the vehicle using the included (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm

Flat Washers, (Figure 2). Do not tighten hardware at this time.

3. Repeat Step 2 for center and rear Mounting Bracket installation, (Figures 3 & 4).

4. IMPORTANT: Use the illustration on this page to identify the sidebars before continuing with the

installation. Verify that the Brackets are in the correct locations as illustrated above. Carefully place the

driver Sidebar onto the Brackets. Align the inserts in the bottom of the Sidebar with the slots on the

Mounting Brackets. Attach the Sidebar to the Mounting Brackets with the included (6) 8mm Hex Bolts,

(6) 8mm Lock Washers and (6) 8mm Flat Washers, (Figure 4). Do not tighten hardware at this time.

5. Level and adjust the Sidebar properly and tighten all hardware.

6. Repeat Steps 2 - 5 for passenger Sidebar installation.

7. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer

over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish.

For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap may be

used also to clean the Sidebar.

For gloss black finishes: Mild soap may be used to clean the Sidebar.

Passenger/Right Side

Rear Mounting Bracket

Passenger/Right Side

Center Mounting Bracket

Passenger/Right Side

Front Mounting Bracket

Front of vehicle

Cradle to

rear

Cradle to rear

Cradle to

rear

Cradle to

rear

32-3/4"

Longer blank end of

sidebar to front

36-3/4"

Dashed line represents approximate location of threaded

inserts in bottom of Sidebar for proper tube identification

1 2

Résumé du contenu

Page 1

3" SIDE BARS 05-12 TACOMA DOUBLE CAB Page 1 of 2 11/23/11 RevC(DP) Driver/Left Side Front Mounting Bracket Driver/Left Side Rear Mounting Brack

Page 2 - 05-12 TACOMA DOUBLE CAB

3" SIDE BARS 05-12 TACOMA DOUBLE CAB Page 2 of 2 11/23/11 RevC(DP) Driver Side Installation Pictured (Fig 1) Drive

Commentaires sur ces manuels

Pas de commentaire

Steelcraft-automotive 230900 3 ROUND SIDE BAR Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Steelcraft-automotive 230900 3 ROUND SIDE BAR. Steelcraft Automotive 230900 3 ROUND SIDE BAR User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Steelcraft-automotive 230900 3 ROUND SIDE BAR