Steelcraft-automotive 230940 3 ROUND SIDE BAR Manuel d'utilisateur télécharger pdf

3" SIDEBAR

2000-06 TOYOTA TUNDRA ACCESS CAB

Page 1 of 3 1/17/12 (DP)

PARTS LIST:

Driver/Left Sidebar

1/2" x 1-1/2" x 15" Long Bolt Plate

Passenger/Right Sidebar

1/2" x 1-1/2" x 4" Short Bolt Plate

Driver/Left Front Mounting Bracket

1/2" x 1-3/8" OD x 3/32" Flat Washers

Passenger/Right Front Mounting Bracket

1/2" Lock Washers

Driver/Left Rear Mounting Bracket

1/2" Hex Nuts

Passenger/Right Rear Mounting Bracket

1/2” x 2” Hex Bolts

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY BEFORE STARTING INSTALLATION.

2. Start installation from under the driver side of the vehicle. Locate the rectangular factory hole in the side

of the frame behind the front body mount, (Figure 1).

3. Select the 1/2" x 15" Long Bolt Plate, (Figure 3B). NOTE: Use the Long Bolt Plate for driver side

installation and the Short Bolt Plate for passenger side front bracket installation. From the back of the

frame, insert the bolt plate into the open end of the boxed frame, (Figure 2), and up to and out of the

rectangular opening in the outside of the frame, (Figure 3A). Line up the top hole in the driver front

Mounting Bracket with the Bolt Plate. Attach the Bracket to the Bolt Plate with (1) 1/2" Flat Washer, (1)

1/2" Lock Washer and (1) 1/2" Hex Nut, (Figure 4). Hand-tighten only at this time.

4. Move towards the rear of the vehicle and locate the factory hole in the frame below the rear body

mount, (Figure 5). Select the driver side Rear Mounting Bracket. From the back of the frame channel,

insert (1) 1/2" x 2" Hex Bolt with (1) 1/2" Flat Washer through the factory hole. Line up the horizontal top

slot in the Bracket with the Hex Bolt, (Figure 6). Attach the Rear Mounting Bracket to the Hex Bolt with

the supplied (1) 1/2" Flat Washer, (1) 1/2" Lock Washer and (1) 1/2" Hex Nut, (Figure 7). Hand-tighten

hardware only at this time.

5. Carefully unwrap the driver Sidebar. Bolt the Sidebar to the Mounting Brackets using the included (2)

1/2” x 2” Hex Bolts, (2) 1/2” Lock Washers and (2) 1/2” Flat Washers, (Figure 8). IMPORTANT: Curved

end of Sidebar will bolt to front Bracket and 90-degree bent end will bolt to rear Bracket. Leave loose at

this time.

6. Level and adjust Sidebar properly and tighten all hardware.

7. Repeat Steps 2 – 6 to install the passenger Sidebar onto the vehicle. NOTE: Use the provided (1) 1/2"

x 4" Bolt Plate to secure the passenger side Front Bracket to the frame channel.

Passenger/Right Front

Mounting Bracket

Passenger/Right Rear

Mounting Bracket

Driver/Left Rear

Mounting Bracket

Driver/Left Front

Mounting Bracket

Bolt Plate (Pictured with hardware)

Long Bolt Plate (Pictured with

hardware)

Passenger/Right

Sidebar

Driver/Left Sidebar

Front

1 2 3

3" SIDEBAR 2

Résumé du contenu

Page 1

3" SIDEBAR 2000-06 TOYOTA TUNDRA ACCESS CAB Page 1 of 3 1/17/12 (DP) PARTS LIST: 1 D

Page 2 - 3" SIDEBAR

3" SIDEBAR 2000-06 TOYOTA TUNDRA ACCESS CAB Page 2 of 3 1/17/12 (DP) 8. Do periodic inspecti

Page 3

3" SIDEBAR 2000-06 TOYOTA TUNDRA ACCESS CAB Page 3 of 3 1/17/12 (DP) Driver Side Installation

Commentaires sur ces manuels

Pas de commentaire

Steelcraft-automotive 230940 3 ROUND SIDE BAR Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Steelcraft-automotive 230940 3 ROUND SIDE BAR. Steelcraft Automotive 230940 3 ROUND SIDE BAR User Manual [es] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Steelcraft-automotive 230940 3 ROUND SIDE BAR